Shure MX185BP Microflex Wired Lavalier Microphone

MX185BP Microflex Wired Lavalier Microphone description:

They're no bigger than a paper clip unless you consider the sound they produce. The Microflex Lavalier microphones bring a new level of sophistication to personal voice reproduction. Like all Microflex family microphones, the Lavaliers use Shure's interchangeable condenser cartridges, available in cardioid, supercardioid or omnidirectional polar patterns. That means you can be sure there's a Microflex Lavalier that's right for your job.

The Microflex Lavaliers are completely compatible with all Shure Wireless transmitters, and their high sensitivity and wide frequency response guarantee great sound with a minimum of RF interference or electromagnetic hum. Plus, each Microflex Lavalier features the same Shure quality sound that has become an industry standard.

Features:

• Pivoting, Single-Microphone Tie Clip, included
• Dual Microphone Tie Clip, included
• Black, Snap-fit Foam Windscreen, included
• Belt-Clip Preamp, included
• 4-foot cable with 4-pin mini connector, included
• Battery/Phantom Powered Preamplifier with Audio Mute Switch, Power LED & Attached 12 ft (4m) Output Cable (MX1BP), included
• Wide dynamic range and frequency response for accurate sound reproduction across the audio spectrum
• Interchangeable cartridges, see our related products area, that provide an optimal choice for each application
• Rotatable tie-clip that pivots in 90 degree incrementsfor placement flexibility
• Supplied snap-fit foam windscreen that controls breath noise and stays on securely
• Balanced, transformerless output for increased immunity to noise over long cable runs
• Supplied dual tie clip holds two microphones for dual miking applications
• MX1BP preamplifier, with Mic Mute/On switch and Power LED, will operate with either a 9 V battery or phantom power

Specifications:

• Type: Condenser (electret bias)
• Frequency Response: 50-17,000 Hz
• Polar Pattern: Cardioid
• Polarity: Positive sound pressure on diaphragm produces positive voltage on pin 2 relative to pin 3 of output XLR connector
• Environmental Conditions: Operatine Temperature Range: -18 to 57 degrees C (0 to 135 degrees F), Storage Temperature Range: -29 to 74 degrees C (-20 to 164 degrees F)
• Microphone Cable: Shielded 1.2 meter (4 ft.) cableterminated with a 4-Pin Female Mini Connector (TA4F)
• Output Impedance: EIA rated at 150 ohms (180 ohms actual)
• Open Circuit Sensitivity (at 1 kHz, ref. 1V/Pa): -54dB (2.0 mV)
• Max SPL (1kHz at 1% THD, 1 kohms load): 140.3 dB
• Equivalent Output Noise (A-weighted): 31.2 dB
• Signal to Noise Ratio (referenced at 94 dB SPL): 62.8dB
• Dynamic Range at 1 kohm load: 109.1 dB
• Common Mode Rejection: 45.0 dB minimum, 10 Hz to 100kHz
• Selectable roll-off Frequency: 100 Hz, with a 12 dBper octave roll-off below this corner frequency
• MX1BP Net Weight: 255 g (9 oz) with attached cabling
• MX1BP Dimensions: 84.3mm H x 65.2mm W x 25.7mm D(3.32" x 2.57" x 1.01")
• Capsule Dimensions: approx. 12mm (0.46") diameter,22mm (0.85") length
• MX1BP Cable: One 3.6m (12 ft) 2 conductor shieldedoutput cable with 3-pin male XLR connector
• Power Requirements: 9V PP3 alkaline battery; 8.4V NiCd rechargeable batter or 9V lithium battery optional; or, from phantom powersource, 10-52V DC
• Battery Life (nominal): 600 continuous hours with 9Valkaline battery
• Battery Current (nominal): 0.8 mA
• MX1BP Input Connector Type: 4-pin Male Mini Connector (TB4M)
• MX1BP Input Configuration: Unbalanced
• MX1BP Output Connector Type: 3-pin Male XLR
• MX1BP Output Configuration: Transformer balanced