Your Feedback

Neumann Monitor Alignment Kit 1

(4)
Item: REC0015278-000
  • Topseller!
Neumann Monitor Alignment Kit 1 Product Image
Enable Social Media
Set of Neumann MA 1 measuring microphone & KH 750 DSP subwoofer. Perfect complement to KH 80 / KH 120 / KH 310 / KH 420.  All product info

Product variations

Neumann MA 1

Neumann MA 1 Product Image
(5)
£ 199.00

Neumann Monitor Alignment Kit 2

Neumann Monitor Alignment Kit 2 Product Image
  • Manufacturer: Neumann
  • Build: 2-Way
  • Interception distance: Near field
  • Bluetooth: No
  • Magnetically shielded: No
  • ...
£ 969.00

Neumann Monitor Alignment Kit 3

Neumann Monitor Alignment Kit 3 Product Image
(1)
£ 1,999.00
£ 1,273.00
incl. VAT, incl. Shipping Costs
or cheap with financing
Ordered, estimated to be in stock: Dec 17, 2021
We are happy to help you!
Our team
Pro Audio & PC
sales@dv247.com
+44 17 0877 1966
+44 17 0877 1901

Activate social media for sharing. Data will only be sent via social networks with your consent.

This item is also available in the following packages

Product information - Neumann Monitor Alignment Kit 1

Neumann Monitor Alignment Kit 1 Overview:

  • MA 1 Measuring microphone
  • KH 750 Subwoofer
  • perfect basis for setting up a frequency-corrected loudspeaker system
  • direct control of the KH 750 by the software
  • DSP preset is stored in the KH 750; after calibrate operation without computer possible
  • compatible with all analog and digital Neumann loudspeakers (loudspeaker configuration is queried by the software during calibrate)
  • Stereo subwoofer setups possible
  • setup with free Neumann Automatic Monitor Alignment software
  • makes it possible to assemble a modern high-end system for recording studios and hi-fi enthusiasts


Neumann MA 1 Application
With the KH 750, the MA 1 system is compatible with all analog Neumann loudspeakers.


State-of-the-art technology for optimally adapted sound

With Neuman's MA 1 calibration system you get a stationary loudspeaker system with perfectly optimised frequency, phase and impulse response according to scientific criteria. Due to its independence from a computer, such a system is also of interest to discerning hi-fi connoisseurs and is even a fairly low-priced alternative to high-end systems in the hi-fi sector.

Set-up effort that pays off.

For correct operation of the Neumann Monitor Alignment Kit 1, in addition to the included Neumann subwoofer, a pair of Neumann loudspeakers is required, as well as a LAN cable for control of each DSP device, 2 XLR cables for connection of the loudspeakers, and 1 additional XLR cable for the measuring microphone during the calibration process. Your DSP-controlled Neumann devices are connected to your computer, if necessary by means of a network switch, and an appropriate number of LAN cables. The LAN network is only required for the calibration process; after calibrate, the EQ and delay curves are stored in the DSPs and the network can be disconnected again.

Neumann Automatic Monitor Alignment Software
Neumann's software guides the user through an automated sequence of calibration steps.


Different setups - one software

The MA-1 measurement microphone is operated for calibration at the microphone input with 48V phantom power of the same audio interface to which the loudspeakers are connected. If the system is to be set up using the digital input on the subwoofer/speaker, a digital audio output is also required on the interface. However, the use of the digital inputs is only supported with the LAN-capable KH 80 DSP. The digital inputs of KH 120 D / KH 310 D drive a DSP module, which is not required for the otherwise analogue speakers in combination with the Monitor Alignment Kit. In this case, use the analogue XLR connectors.

Neumann Automatic Monitor Alignment calibration software
Finally, the generated curve is displayed and can be adjusted.


All in all, there are several possibilities for the connection from the interface to the box(es):

  • AES/EBU: The digital output in XLR format requires a line with 110Ohm impedance, but the unbalanced AES3 input with BNC socket at the box requires a signal with 75Ohm source impedance. Strictly speaking, an impedance converter must be connected in between.* This method achieves the best results. Experience has shown, however, that an adapter from XLR to BNC is sufficient.
  • S/PDIF: The specifications of the S/PDIF standard are included in the AES3 standard. So an S/PDIF output can be connected to the BNC input with a simple plug-in adapter oder adapter cable and will be recognized by the DSP without any problems.
  • Analog: It is of course equally possible to drive the DSP via the analog XLR input and at the same time benefit from the advantages of speaker correction with the MA-1. In this case, however, you have to accept an additional conversion step (analog input to DSP).

Detailed documentation and the required, free Neumann Automatic Monitor Alignment software are available in the Neumann download area.

Please be sure to switch off Direct Monitoring on the interface during the calibration process; otherwise you risk damage to your loudspeakers due to a feedback loop! To do this, turn the source selector from Input to DAW, if necessary.

This task can also be performed by a suitable resistor network (T-element).

Department Information - Pro Audio

Music Store professional in Cologne

MusicStore-MusicStoreShop:/department-footer/MusicStore_Aussen_Neu_schmaler.jpg

DV247 Music Store in London

DV 247 Store in London Romford

Video: Pro Audio

Recording Center

MusicStore-MusicStoreShop:/department-footer/ProAudio-1.jpg

Pro Audio - Picture Gallery

MusicStore-MusicStoreShop:/department-footer/ProAudio-4.jpg